Other products / Other products
SaniForce 3150 HS Ball Pumps
Specification
| SaniForce HS 3150 Pump | |
| Maximum fluid working pressure | 120 psi ( 0.8 MPa, 8 bar ) |
| Air pressure operating range | 20 ~ 120 psi ( 0.14 ~ 0.8 MPa, 1.4 ~ 8 bar ) |
| Maximum air consumption | 175 scfm |
| Air consumption at 70 psi air inlet pressure / 60 gpm | 50 scfm |
| Maximum free flow delivery | 160 gpm ( 606 liter / min. ) |
| Maximum pump speed | 145 cpm |
| Gallons ( liters ) per cycle | 1.03 ( 3.9 ) |
| Maximum suction lift ( flapper ) | Wet: 10 ft ( 3.5 m ) Dry: 5 ft ( 1.75 m ) |
| Maximum suction lift ( ball ) | Wet: 18 ft ( 5.5 m ) Dry: 9 ft ( 2.75 m ) |
| Maximum size pumpable solids ( flapper ) | 2.5” ( 63.5 mm ) |
| Maximum size pumpable solids ( ball ) | 1” ( 25.4 mm ) |
| Maximum noise level at 100psi, full flow | 90 dBa |
| Sound power level | 103 dBa |
| Noise level at 70 psi and 50 cpm | 85 dBa |
| Maximum fluid operating temperature is based on the following maximum diaphragm, ball and seat temperature rating. | PTFE balls: 220℉ ( 104.4℃ ) PTFE/ EPDM Overmolded ( HD ) diaphragm: 180℉ ( 82.2℃ ) Santoprene balls or diaphragm: 180℉ ( 82.2℃ ) 3A Approved EPDM Overmolded diaphragm: 275℉ ( 135℃ ) Buna-N balls or diaphragm: 180℉ ( 82.2℃ ) Fluoroelastomer balls or diaphragm: 250℉ ( 121.1℃ ) |
| Air inlet size | 0.5 inch npt (f) |
| Wetted materials on all models | 316 SST, 3A Approved EPDM |
| Wetted material depending on model | 316 SST, Santoprene, Buna-N, fluoroelastomer, 3A Approved EPDM, PTFE. |
| Non-wetted external parts | 300 series stainless steel, Polyester ( lables ), LDPE foam ( gasket ) |
| Weight | 145 lb ( 66 kg ) |
| Size | |
SaniForce 3150 HS Ball Pumps:
| P/N | Type | Inlet | Diaphragm | Ball Material |
| SA13A1 | Ball Check | 1.5 in x 1.5 in | Overmolded PTFE/EPDM | PTFE |
| SA23A1 | Ball Check | 2 in x 2 in | Overmolded PTFE/EPDM | PTFE |
| SA3AA1 | Ball Check | 3 in x 3 in | Overmolded EPDM | PTFE |
| SA33A1 | Ball Check | 3 in x 3 in | Overmolded PTFE/EPDM | PTFE |
| SA4AA1 | Ball Check | 4 in x 4 in | Overmolded EPDM | PTFE |
| SA43A1 | Ball Check | 4 in x 4 in | Overmolded PTFE/EPDM | PTFE |
| SA53A1 | Ball Check | 3 in x 2 in | Overmolded PTFE/EPDM | PTFE |
| SA3361 | Ball Check | 3 in x 3 in | Overmolded PTFE/EPDM | Santoprene |
| SB2AA1 | Ball Check | 2 in x 2 in | Overmolded EPDM | PTFE |
| SB3AA1 | Ball Check | 3 in x 3 in | Overmolded EPDM | PTFE |
| SB2661 | Ball Check | 2 in x 2 in | Santoprene | Santoprene |
| SB3661 | Ball Check | 3 in x 3 in | Santoprene | Santoprene |
| SB2771 | Ball Check | 2 in x 2 in | Buna-N | Buna-N |
| SB3771 | Ball Check | 3 in x 3 in | Buna-N | Buna-N |
| SB2881 | Ball Check | 2 in x 2 in | Fluoroelastomer | Fluoroelastomer |
| SB3881 | Ball Check | 3 in x 3 in | Fluoroelastomer | Fluoroelastomer |
Performance Charts
Dimensions
